Below is a replacement chart for gears of Samhongsa brass diesel locomotives. This chart was created by Gene Maddox and contains quite a lot of good information and can be found on Mark's website below. Have fun with it.
http://www.spookshow.net/brass.html
This blog will show the evolution of The "New" JJJ&E. The "New" JJJ&E is an N scale layout that was started in February 2009 and replaced The "Original" JJJ&E which was in operation for over nine years. The "new" JJJ&E is located in a train room 12'x21'. The layout is an inverted "U" shape along the perimeter of the train room.
The JJJ&E Logo
Thursday, July 30, 2015
It's Been Awhile.......
It's been awhile since I last posted on my blog. All is well here and I'll be adding some new posts in the days ahead. My layout is progressing slowly after completing almost 100% of the basic scenery. The "new" JJJ&E is well into its seventh year of operation. I am busy adding details to the many scenes on the layout. This all takes time, and as you get older, completed projects occur at a slower rate. One of the main projects I completed some time ago was adding rock work behind the 24 stall Roundhouse. This took time to complete as the rock work had to be completely weathered. The rock work is located in the 50 inch turnaround area behind the Roundhouse. I also had to build a backdrop for the rock work to rest against. The backdrop followed the natural curve of the bench work at that end of the layout.. I also have to add more vegetation that is growing in the crevices of the finished rock work. I'll take some photo's of the finished scene in several days. The view of the rock work will be seen from the diesel service yard at the opposite end of the Switching Yard.
Stay cool and run steam..... PSG1790
Stay cool and run steam..... PSG1790
Sunday, April 5, 2015
DCC Default Decoder Reset Values
Published in Train Talk, the newsletter of the Daring Downs Model Rwy Club, Queensland Division, AR
Website: http://http://www.ddmrc.com.au/
DCC Decoder Default Resets
Ted Freeman
A not uncommon problem with mobile DCC decoders is losing settings as occurs at times when a short circuit is experienced on the track feed, or making mistakes when changing CV’s (Configuration Variables). The best way to overcome a problem such as this is to reset the decoder to its default factory settings and start over (if you are using JMRI or some such, keep records of settings).
Many decoders returned for repair could have been reset to factory settings.
Since the factory reset is not in the NMRA DCC standards or recommended practices, each manufacturer can do their own thing. If you do not know the manufacturer of your decoder, you can try reading CV8 on the program track. This is a read only CV that has the manufacturer’s ID number (numbers are shown in decimal)
Listed here are the most common Decoder ID’s and reset procedures. For other decoders check the manual for CV and value used to reset to factory settings. All these decoders do support Ops Mode programming and can be reset on the mainline assuming you have control of the address.
If you do not have control of the address use the program track.
Manufacturer ID # In CV8 CV Value for reset
Lenz 99 CV8 = 33
NCE 11 CV30 = 2
Digitrax 12 CV8 = 8
LokSound (ESU) 15 CV8 = 8
Train Control System 153 CV8 = 8 or CV30 = 2
SoundTraxx: DSDLC, DSXTsunami 1141 CV 30 = 2 CV8= 8
MRC (New) 2143 CV125 = 1
QSI 11131 Generally requires PowerPax, Programming Track Booster2 Generally is not reliable in Read-Back
To Reset a Decoder
Start by determining the decoder manufacturer.
On the program track read CV 8.
Published in Train Talk, the newsletter of the Daring Downs Model Rwy Club, Queensland Division, AR
Website: http://http://www.ddmrc.com.au/
Compare the number with the above chart for the ID (if you have a QSI decoder [ID 113]
Then write to the matching CV the value as shown in the chart (writing a number to CV 8 will not change the value in CV8 when you read it back). When resetting the decoder, it may respond by flashing the lights or tooting the horn. Resetting a decoder will change the address back to the default of 3.
Try the decoder on the main line using address 3 to be sure everything is okay. Then you can start your programming.
Resetting QSI Decoders to factory default
The Broadway, Atlas, and Lifelike equipped with QSI (ID 113) DCC sound engines
use a different reset procedure. Check the manual that came with the engine.
Some use a magnetic “wand” for the reset. If there is no “wand” then open the engine
or access hatch and find the reset jumper. Remove the jumper and restore the track power.
There will be an audible acknowledgment from the engine at the end of the reset
sequence (usually 3 toots of the whistle/horn). Replace the jumper and test out using address 3.
If a “wand” is present, locate the internal reset reed switch and place the “wand” over
it for a moment. When track power is restored the engine will go through its reset
procedure and let you know when done.
To find the internal reset (reed) switch, place the engine on active track. Slowly move
the “wand” over the top of the engine or tender until the engine alerts you, audibly responds, by a message.
QSI also has a user software reset using the following multi step procedure:
(1) Place engine on main track if it is still responding to its address. If not responding you may need to use the program track.
(2) Set CV49 to 128
(3) Set CV50 to 255
(4) Set CV56 to 113
As the decoder in the engine resets you will hear an audible response, 3 toots or it may talk to you.
Test the locomotive using address 3.
You can then go ahead and set the loco number as you desire and/or reprogram other CV’s. An irritating part with the QSI decoders is that when they do get corrupted by a short, the locomotive affected can be very erratic in operation, resetting to default will put you back in control of its performance.
In this day of instant gratification, the Internet can provide many answers and/or suggestions
Thursday, January 15, 2015
Hard Wiring A UP FEF #844 Steam Locomotive Using The Original Light Board
I have two UP FEF #844 steam locomotives. The first #844 was hardwired with a ESU Lok-Sound Micro Version 4 decoder with two Zimo cube speakers. This FEF runs and sounds beautifully as the ESU Lok_Sound Micro decoder has outstanding motor and sound functions.
The second UP FEF #844 I purchased with a factory installed TCS K6D4 decoder. Unfortunately, the UP FEF has issues at very slow speeds.
TCS has offered to reprogram these K6D4 decoders if they are returned to the TCS factory. Due to the large train show in Springfield Massachusetts on January 25 and 26th, any decoders sent back to TCS will not be returned to users until late February to early March 2015 as I was told when I called TCS yesterday.
If by chance, you decide to order a new TCS K6D4 decoder on their website, you will receive the original version of this decoder and not the new re-programmed decoder. According to TCS, they haven't completely figured out the fix for the K6D4 decoder. I was also told not to change any of the CV's on the original K6D4 decoder. You, as a consumer cannot fix this decoder.
In any event, I decided to hard wire a decoder to the original light board of the UP FEF. When I received the factory installed TCS K6D4 decoder in the UP FEF, Kobo didn't include the original light board of the locomotive which was removed when they installed the TCS K6D4 decoder in the locomotive..
I then decided to order an original light board from the Kato parts department and I should receive it in the next few days. The cost of the light board is $5 plus shipping.
Meanwhile in late December of 2014, a member of RW forum published a diagram for hard wiring a decoder to the light board. It is listed below. If you carefully follow the diagrams you'll be able to hard wire a decoder in this locomotive. I'll be using a small Zimo N scale MX621 miniature Lok decoder which is tiny and should fit in a space behind the original light board. I'll be soldering the wiring to this light board on my work bench and then install the finished product into the UP FEF.
John Columbo of the RW and TB forums recommended using this decoder in the UP FEF as it has outstanding motor functions and performs well with the UP FEF's new coreless motor. It's small size allows you to easily slip the decoder in place in the locomotive with no adjustments to the locomotive frame.
In this FEF I'll be installing a Soundtraxx Heavy Steam decoder made for the UP FEF in the tender with several Zimo cube speakers. This is what is called a "two decoder" approach. Only the sound functions of the Soundtraxx decoder will be used .
I've used this "two decoder" approach in all of my previous Soundtraxx decoder installations. In those installations I used a Lenz mini silver decoder for motor functions as the Soundtraxx decoders' motor functions are poor at best. The Soundtraxx decoder was used for sound functions only. It's an added cost, but the "two decoder" approach is worth the added cost and effort.
The second UP FEF #844 I purchased with a factory installed TCS K6D4 decoder. Unfortunately, the UP FEF has issues at very slow speeds.
TCS has offered to reprogram these K6D4 decoders if they are returned to the TCS factory. Due to the large train show in Springfield Massachusetts on January 25 and 26th, any decoders sent back to TCS will not be returned to users until late February to early March 2015 as I was told when I called TCS yesterday.
If by chance, you decide to order a new TCS K6D4 decoder on their website, you will receive the original version of this decoder and not the new re-programmed decoder. According to TCS, they haven't completely figured out the fix for the K6D4 decoder. I was also told not to change any of the CV's on the original K6D4 decoder. You, as a consumer cannot fix this decoder.
In any event, I decided to hard wire a decoder to the original light board of the UP FEF. When I received the factory installed TCS K6D4 decoder in the UP FEF, Kobo didn't include the original light board of the locomotive which was removed when they installed the TCS K6D4 decoder in the locomotive..
I then decided to order an original light board from the Kato parts department and I should receive it in the next few days. The cost of the light board is $5 plus shipping.
Meanwhile in late December of 2014, a member of RW forum published a diagram for hard wiring a decoder to the light board. It is listed below. If you carefully follow the diagrams you'll be able to hard wire a decoder in this locomotive. I'll be using a small Zimo N scale MX621 miniature Lok decoder which is tiny and should fit in a space behind the original light board. I'll be soldering the wiring to this light board on my work bench and then install the finished product into the UP FEF.
John Columbo of the RW and TB forums recommended using this decoder in the UP FEF as it has outstanding motor functions and performs well with the UP FEF's new coreless motor. It's small size allows you to easily slip the decoder in place in the locomotive with no adjustments to the locomotive frame.
In this FEF I'll be installing a Soundtraxx Heavy Steam decoder made for the UP FEF in the tender with several Zimo cube speakers. This is what is called a "two decoder" approach. Only the sound functions of the Soundtraxx decoder will be used .
I've used this "two decoder" approach in all of my previous Soundtraxx decoder installations. In those installations I used a Lenz mini silver decoder for motor functions as the Soundtraxx decoders' motor functions are poor at best. The Soundtraxx decoder was used for sound functions only. It's an added cost, but the "two decoder" approach is worth the added cost and effort.
Wednesday, January 7, 2015
How To Remove A Number, Logo Or Lettering From A Locomotive Or Rolling Stock
Removing lettering, numbers, or logos from a locomotive or rolling stock can be a challenging proposition. The video below makes removing numbers, letters or logos from N scale equipment an easy technique. This technique can also be used in other scales as well. This video and technique comes from the ATHEARN Facebook page.
Below is the link for this video.
https://www.facebook.com/video.php?v=10152936814060041
Saturday, December 27, 2014
Top-Hobby Trains Sound Decoder Installation Videos In The Kato UP FEF #844
Top Hobby Trains Kato UP FEF #844 Northern With ESULokSound Version 4 DCC
Sound Video
Top Hobby Trains Kato UP FEF #844 Northern Sound Package With Soundtraxx DCC N Scale Tsunami Sound
Friday, December 26, 2014
TSU-750 Micro Tsunami Heavy Steam Soundtraxx Decoder Installation In A Kato UP FEF #844
Below is the link to the Soundtraxx Website showing a TSU-750 Micro Tsunami Heavy Steam decoder in a Kato UP FEF #844. This is a difficult installation and will take considerable time to accomplish.
http://www.soundtraxx.com/documents/appnotes/kato_fef3_n-scale.pdf
http://www.soundtraxx.com/documents/appnotes/kato_fef3_n-scale.pdf
TCS K6D4 Decoder Installation In A UP FEF #844
Below is the link for the TCS K6D4 Decoder Installation In the "new" Kato UP FEF #844. This is a rather easy installation of the TCS K6D4 decoder. It simply replaces the original board in the Kato UP FEF #844. Have fun with it.
http://www.tcsdcc.com/Customer_Content/Installation_Pictures/N_Scale/Kato/FEF%204-8-4/FEF4-8-4_K6D4.html
Thursday, December 25, 2014
The "Dither" Factor IN A TCS decoder for the Kato UP FEF #844
THE Kato FEF UP # 844 uses a K6D4 drop-in decoder. With this decoder you can't manually control the BEMF feature which causes the steam locomotive to start too fast and lunge out of control at times during operations. To correct this, the BEMF must be set to zero. (CV 61=0). The factory setting is to leave the BEMF on. (CV 61=1).
You then must adjust CV's 56 and 57 to actually obtain very slow speeds. This is very similar to the feature of CV 61 (BEMF) in Digitrax decoders. CV 56 and CV 57 must manually be adjusted in the Digitrax decoders to slow down the speed of the locomotive.
In the TCS decoder for the UP FEF #844, initially set CV 56 to 3 and CV 57 to 25. You then can adjust CV 56 and CV 57 in increments to obtain the desired speed results that you are looking for. It is all a mater of trial and error.
You can also set CV 57 to 0 to turn off the "dither effect" to see how the locomotive works with this CV turned off.
The excerpt below is from the TCS Website.
"Dither is digital pulse power. It is similar to "pulse power" that is used on DC power packs. It helps overcome the "stiction" of locomotive mechanics. With CV56 you control the frequency of the pulses and with CV57 you control the amplitude of the pulses. It provides better and smoother low-speed performance. Dither is especially helpful on locomotives that have high starting friction. There are two parameters that control the operation of Dither in TCS Decoders. Program the frequency of the additional pulse by putting a value in CV56. A value of 1 will give the highest frequency of additional pulses per second. We recommend starting with a value of 3 in CV56 which is the factory default. Values of 1 thru 255 are valid. Most locomotives will work best with a value of 3 in CV56. Typical values are between 1 and 10. CV57 controls the amplitude of Dither pulses. We recommend starting with a value of 25 in CV57. Then adjust CV57 up or down 5 at a time and test operation until you you find the value that works best for your loco. Valid values are from 1 to 255. (1 being the lowest amplitude pulse and 255 being the highest.) Most locomotives being manufactured today will work very nicely with a value between 15 and 35 in CV57. There are some older locomotive models that could benefit from a higher value of Dither amplitude in CV57. For some older locomotives that are particularly sticky a value of 75 to 90 might be necessary to help smooth the slow speed response. When CV57 has a value of 0, Dither is disabled. When CV57 has a value greater then zero it is active. It is active through the whole speed range and in all speed step modes (14,28,128). It is active with user loadable speed table, Vstart, Vmid, Vhigh. Try experimenting with Dither to achieve better low-speed operation. The effect will narrow the window between what point the locomotive starts to move and at what point it will stay running. There are two parameters that control the operation of Dither in TCS Decoders. Program the frequency of the additional pulse by putting a value in CV56. A value of 1 will give the highest frequency of additional pulses per second. We recommend starting with a value of 3 in CV56 which is the factory default. Values of 1 thru 255 are valid. Most locomotives will work best with a value of 3 in CV56. Typical values are between 1 and 10. CV57 controls the amplitude of Dither pulses. We recommend starting with a value of 25 in CV57. Then adjust CV57 up or down 5 at a time and test operation until you you find the value that works best for your loco. Valid values are from 1 to 255. (1 being the lowest amplitude pulse and 255 being the highest.) Most locomotives being manufactured today will work very nicely with a value between 15 and 35 in CV57. There are some older locomotive models that could benefit from a higher value of Dither amplitude in CV57. For some older locomotives that are particularly sticky a value of 75 to 90 might be necessary to help smooth the slow speed response. When CV57 has a value of 0, Dither is disabled. When CV57 has a value greater then zero it is active. It is active through the whole speed range and in all speed step modes (14,28,128). It is active with user loadable speed table, Vstart, Vmid, Vhigh. Try experimenting with Dither to achieve better low-speed operation. The effect will narrow the window between what point the locomotive starts to move and at what point it will stay running".
You then must adjust CV's 56 and 57 to actually obtain very slow speeds. This is very similar to the feature of CV 61 (BEMF) in Digitrax decoders. CV 56 and CV 57 must manually be adjusted in the Digitrax decoders to slow down the speed of the locomotive.
In the TCS decoder for the UP FEF #844, initially set CV 56 to 3 and CV 57 to 25. You then can adjust CV 56 and CV 57 in increments to obtain the desired speed results that you are looking for. It is all a mater of trial and error.
You can also set CV 57 to 0 to turn off the "dither effect" to see how the locomotive works with this CV turned off.
The excerpt below is from the TCS Website.
"Dither is digital pulse power. It is similar to "pulse power" that is used on DC power packs. It helps overcome the "stiction" of locomotive mechanics. With CV56 you control the frequency of the pulses and with CV57 you control the amplitude of the pulses. It provides better and smoother low-speed performance. Dither is especially helpful on locomotives that have high starting friction. There are two parameters that control the operation of Dither in TCS Decoders. Program the frequency of the additional pulse by putting a value in CV56. A value of 1 will give the highest frequency of additional pulses per second. We recommend starting with a value of 3 in CV56 which is the factory default. Values of 1 thru 255 are valid. Most locomotives will work best with a value of 3 in CV56. Typical values are between 1 and 10. CV57 controls the amplitude of Dither pulses. We recommend starting with a value of 25 in CV57. Then adjust CV57 up or down 5 at a time and test operation until you you find the value that works best for your loco. Valid values are from 1 to 255. (1 being the lowest amplitude pulse and 255 being the highest.) Most locomotives being manufactured today will work very nicely with a value between 15 and 35 in CV57. There are some older locomotive models that could benefit from a higher value of Dither amplitude in CV57. For some older locomotives that are particularly sticky a value of 75 to 90 might be necessary to help smooth the slow speed response. When CV57 has a value of 0, Dither is disabled. When CV57 has a value greater then zero it is active. It is active through the whole speed range and in all speed step modes (14,28,128). It is active with user loadable speed table, Vstart, Vmid, Vhigh. Try experimenting with Dither to achieve better low-speed operation. The effect will narrow the window between what point the locomotive starts to move and at what point it will stay running. There are two parameters that control the operation of Dither in TCS Decoders. Program the frequency of the additional pulse by putting a value in CV56. A value of 1 will give the highest frequency of additional pulses per second. We recommend starting with a value of 3 in CV56 which is the factory default. Values of 1 thru 255 are valid. Most locomotives will work best with a value of 3 in CV56. Typical values are between 1 and 10. CV57 controls the amplitude of Dither pulses. We recommend starting with a value of 25 in CV57. Then adjust CV57 up or down 5 at a time and test operation until you you find the value that works best for your loco. Valid values are from 1 to 255. (1 being the lowest amplitude pulse and 255 being the highest.) Most locomotives being manufactured today will work very nicely with a value between 15 and 35 in CV57. There are some older locomotive models that could benefit from a higher value of Dither amplitude in CV57. For some older locomotives that are particularly sticky a value of 75 to 90 might be necessary to help smooth the slow speed response. When CV57 has a value of 0, Dither is disabled. When CV57 has a value greater then zero it is active. It is active through the whole speed range and in all speed step modes (14,28,128). It is active with user loadable speed table, Vstart, Vmid, Vhigh. Try experimenting with Dither to achieve better low-speed operation. The effect will narrow the window between what point the locomotive starts to move and at what point it will stay running".
Friday, December 12, 2014
Decoder Installation In An Atlas Two Truck Shay
I installed the Lenz 521W decoders in the Atlas Two Truck Shay in 2005. Today I would use a TCS Z scale decoder or a Digitrax Z scale decoder. The decoder of choice for any installations in 2014 would be the TCS Z scale decoder. By using the TCS Z scale decoder, it won't be necessary to remove much bulk from the interior of the cab and oil bunker.
Below is the installation of a Lenz 521W decoder in an Atlas Two Truck Shay.
Atlas is re-issuing new Two Truck Shay's in 2015, so this decoder installation is quite relevant.
I have five Atlas two truck Shay's and have installed Lenz 521W decoders in each one of them.
I was asked by several individuals on the Atlas Forum to post tutorial pictures of the process.
Looking back, I suppose I should have taken pictures, but I didn't find the "decoder installation" in the Atlas Two truck Shay to be that intimidating as long as you take your time.
I'll try and explain it verbally. First the Atlas two truck Shay is a delicate locomotive. However don't let the small size of the loco intimidate you at all.
First make sure the loco is properly cradled . Also work in an area where there is a white table and light flooring. You will also need some magnifying loops.
Remove both front and rear couplers with a very small Phillips screwdriver.
When the couplers are removed, they will immediately fall into five pieces.; the two parts of the coupler, the top and bottom portion of the coupler box and a spring that's smaller than a MT Z scale #905 spring. Don't worry about the five pieces of the original coupler; you're not going to use it. You'll install a MT Z scale #905 coupler instead on the front and rear of the loco.
Next remove the four screws, two on each end that hold the main frame in position. Carefully place these screws in a safe place and keep the two front screws and two rear screws in separate places.
The frame will lift off from the shell when the screws are removed.
You can easily remove the cab. The oil bunker is attached to the cab and it can be removed by loosening the screw that holds the oil bunker in position on the cab.
Now to the decoder.
We want to place the Lenz 521W decoder so that the leading edge of the decoder is right at the midpoint of the cab windows where the vertical post is located that separates the two windows. It also has to be slightly angled upwards.
To be able to get to this position , you must carefully remove some bulk from the interior of the cab and oil bunker. Enough material must be removed so the oil bunker screw can be replaced to hold the oil bunker in position on the cab after the decoder is in position.
This is the only difficult part of the installation.
It will be trial and error to get the right amount of material removed from the cab and oil bunker, but it can be done with some patience.
Check the decoder in the cab to get the right positioning.
The red and black wire of the decoder go to the right and left pick-ups. Kapton tape must be used between the pickups and the frame.
You can bend the tabs away from the pickup strips to isolate the frame.Use some Kapton tape here.
The orange wire goes to the right motor terminal and the gray wire goes to the left motor terminal.
The blue and white wires connect to the leds which are bi-directional. Wrap some kapton tape over the top of the blue and white wires to the leds.
Now test out the decoder before you reinstall the shell to the frame. Screw the oil bunker back to the cab and seat the cab on the shell.
After the decoder installation has been successfully tested, gently place the shell on the loco. Be careful not to pinch the wiring going to the leds and be careful about getting the leds in their proper relationship to the shell.
With the shell firmly in place. screw in the four screws that hold the shell on the frame.
Now we have to deal with the couplers. The N scale coupler that Atlas uses on the two Truck Shay is grossly out of proportion to the rest of the loco. They look like "giant appendages" hanging off each end of the loco.
Put the 10 parts form the coupler in a small container in the loco jewel box and forget about them.
We'll use a MT Z scale #905 on each end of the loco. This will give give you a truly proportional coupler in relation to the loco. It looks fantastic.
You won't be able to screw this coupler in the original hole that Atlas used for it's N scale coupler. The Z scale coupler box is longer than the original coupler but don't worry.
Test the positioning of the Z scale coupler on the frame. If you put it back too far, it will interfere with the truck movement. The ideal position for the coupler is that you can just see the anterior edge of the hole for the screw when you look down on the loco.
You can test the movement of the trucks to get a feeling where the # 905 is to placed.
We are going to use CA cement to cement the coupler to the frame. The Z scale coupler doesn't have to be shimmed. Now placed a very fine layer of Ca cement on the frame where the coupler is to be positioned.
You don't want much cement, as you don't want the cement to interfere with the action of the coupler.
Seat your coupler on the frame of the loco in the space where the coupler box should rest. Make sure that you can just see the anterior part of the hole that holds the screw when you look down on the loco.
As the cement sets up you can check the height of the couper with another car. Chances are there will be no adjustments.
Let the cement set up completely before running the loco.I would wait several hours.
Now enjoy your Atlas two truck Shay with a Lenz 521W decoder. You can also use a Lenz 511 decoder if you don't want the BEMF function. A Digitrax DZ 123 and a Digitraz DZ 143 will also fit the loco.
I happen to like Lenz decoders.
With the Lenz 521W decoder installed, The Two truck Shay is amazing at very slow speeds.
You can modify the loco's performance by adjusting CV 2, CV3, CV4 and CV 9. The BEMF function can be adjusted by adjusting CV 50 bit 0 to 1 . This activates the BEMF control of the decoder.
Enjoy the installation.
Stay cool and run steam......
Subscribe to:
Posts (Atom)
